|
|
"2670" - Coil Mounting Bracket - $23 Each This coil mounting bracket is accurately punched & sheared from correct gauge material with the factory-style extruded & tapped hole for the clamping screw. Comes complete with a cadmium plated slotted machine screw with self-tapping end. Correct silver cadmium plated as original distinguishes this part from the rest of the reproductions that are only zinc plated. Used on 1967-79 small block applications. Reference part #2642 670. |
|
|
"8207" - Coil Mounting Bracket - $23 Each This coil mounting bracket is accurately punched & sheared from correct gauge material with the factory-style extruded & tapped hole for the clamping screw. Comes complete with a cadmium plated slotted machine screw with self-tapping end. Correct silver cadmium plated as original distinguishes this part from the rest of the reproductions that are only zinc plated. Used on big block, hemi, and 6 cylinder applications. Reference part #1688 207. |
 |
"750" - ECU Mounting Bracket Kit - $32 Per Kit Concours-quality reproduction of the Electronic Ignition Control Unit mounting bracket for 1972-74 E-Body cars. Made from correct heavy gauge steel and zinc dichromate plated for original appearance. Mounts on the firewall as original, or inner fender panel if desired for other applications. Includes four correct zinc plated 1/4” anchor-headed screws for mounting. Reference part #3513 750.
|
|
|
"5236" - Wiring Clip - $10 Each
Excellent reproduction of the wiring clip found on the upper left bell housing-to-engine block attaching bolt for both manual and automatic transmission equipped cars. Used to route the reverse light/neutral safety wiring harness from the firewall bulk head to the transmission switch. Also found in conjunction with part #AX41T on 4-speed side covers. Formed from correct gauge steel, zinc plated, and thermoplastic coated for original appearance. Reference Chrysler part number 6015 236.
|
 |
"5707" - Wiring Clip - $10 Each
Excellent reproduction of the wiring clip found on either of the upper automatic transmission tail shaft attaching bolt. Used to route the reverse light/neutral safety wiring harness from the firewall bulk head to the transmission switch. Once in place, the clip is bent forward to rest on the transmission housing. Formed from correct gauge steel, zinc plated, and thermoplastic coated for original appearance. Reference Chrysler part number 6015 707. |
 |
"007" - Alternator Mounting Kit - $45 Per Kit 1966 & Earlier Big Block Engine without A/C. Fits water pumps with casting numbers 2205 862, 2468 007, & 2536 767. POWDER COATED low gloss black. Comes complete with mounting triangle, adjusting strap, (3) phosphated spacers, (4) OE correct bolts and (2) conical washers. See #987B description below. View Proper Component Orientation
|
|
"987" - Alternator Mounting Kit - $45 Per Kit 1967-1974 Big Block Engine without A/C. Fits water pumps with casting numbers 2780 987 & 3698 468. POWDER COATED low gloss black. Comes complete with mounting triangle, adjusting strap, (3) phosphated spacers, (4) OE correct bolts and (2) conical washers. See #987B description below. View Proper Component Orientation
|
|
"007H" - Alternator Mounting Kit - $45 Per Kit 1964-1966 426ci Hemi Engine fits water pumps with casting numbers 2205 862, 2468 007, & 2536 767. POWDER COATED low gloss black. Comes complete with mounting triangle, adjusting strap, (3) phosphated spacers, (4) OE correct bolts and (2) conical washers. See #987BH description below. |
|
"987H" - Alternator Mounting Kit - $45 Per Kit 1967-1971 426ci Hemi Engine fits water pumps with casting numbers 2780 987 & 3698 468. POWDER COATED low gloss black. Comes complete with mounting triangle, adjusting strap, (3) phosphated spacers, (4) OE correct bolts and (2) conical washers. See #987BH description below. View Proper Component Orientation
|
|
"794" - Alternator Mounting Kit - $40 Per Kit 1967-1969 Small Block Engine fits cast iron water pumps with casting numbers 2402 794 & 2863 067. POWDER COATED low gloss black. Comes complete with mounting triangle, adjusting strap, (3) phosphated spacers, one bolt and a conical washer. See #794B description below. View Proper Component Orientation
|
|
"795" - Alternator Mounting Kit - $40 Per Kit 1970 & Later Small Block Engine fits aluminum water pump with part number 3420 037. POWDER COATED low gloss black. Used on non-A/C applications. Comes complete with mounting triangle, adjusting strap, (2) phosphated spacers, one bolt and a conical washer. See #795B description below. Use heater hose support "AX43" View Proper Component Orientation
|
 |
"6040-KIT" - Alternator Mounting Kit - $199 Per Kit 1967-1968 Big Block Engines with Air Conditioning Comes complete with cast alternator mounting bracket, adjusting strap, alternator support bracket, cast idler pulley spacer, idler pulley bracket with pulley, heater hose bracket, and all correct phosphate mounting hardware.
|
 |
"1746B-KIT" - Alternator Mounting Kit - $189 Per Kit 1969-1972 383 & 400 Big Block Engines with Air Conditioning Comes complete with alternator mounting triangle, formed adjusting strap, alternator mounting block with phosphate spacers, cast idler pulley spacer, idler pulley bracket with pulley, heater hose bracket, and all correct phosphate mounting hardware.
|
 |
"1746RB-KIT" - Alternator Mounting Kit - $189 Per Kit 1969-1972 440 Big Block Engines with Air Conditioning Comes complete with alternator mounting triangle, formed adjusting strap, alternator mounting bolt with phosphate spacers, cast idler pulley spacer, idler pulley bracket with pulley, heater hose bracket, and all correct phosphate mounting hardware.
|
|
"6040" - Alternator Mounting Bracket - $65 Each An excellent reproduction of the cast alternator mounting bracket used on all 1967-68 Big Block engines with Air Conditioning. This bracket is cast in high-strength aluminum instead of the heavier cast iron of originals, and is dipped in low-gloss black for original appearance. Includes correct alternator mounting bolt and special hug-lok nut, and three OE correct bracket mounting bolts. Mounts to front of right cylinder head. Reference P/N 2806 040. |
 |
"987TAC" - Alternator Mounting Triangle - $25 Each 1969-74 Big Block Engine with Air Conditioning. Fits all big block water pumps. Has correct locating dimple and 5/16-18 weld nut for heater hose shield #0058. POWDER COATED low gloss black. Use heater hose support "0058"
|
 |
"007T" - Alternator Mounting Triangle
- $25 Each
1966 & Earlier Big Block & Hemi Engine without A/C. Fits water pumps with casting numbers 2205 862, 2468 007, & 2536 767. POWDER COATED low gloss black. |
 |
"987T" - Alternator Mounting Triangle - $25 Each 1967-1974 Big Block & Hemi Engine without A/C. Fits water pumps with casting numbers 2780 987 & 3698 468. POWDER COATED low gloss black. Reference Chrysler part number 2658 990. |
 |
"987S" - Alternator Adjusting Strap - (1) Required - $10 Each 1966-74 Big Block without A/C alternator adjusting strap. POWDER COATED semi-gloss black. Reference Chrysler part number 2206 446.
|
 |
"987SAC" - Alternator Adjusting Strap - (1) Required - $23 Each 1967-68 Big Block with A/C alternator adjusting strap with heater hose shield. POWDER COATED semi-gloss black with the shield thermo-plastic coated. Use with #V2 hose bracket. Reference Chrysler part number 2899 110.
|
 |
"987SH" - Alternator Adjusting Strap - (1) Required - $10 Each 1966-71 426 Hemi alternator adjusting strap. POWDER COATED semi-gloss black. Reference Chrysler part number 2780 630.
|
 |
"3057" - Alternator Support Bracket - (1) Required - $15 Each A quality reproduction if the alternator support bracket used on 1967-68 Big Block applications with Air Conditioning. Mounts between the idler pulley bracket and alternator. Formed from the correct gauge steel and powder coated low gloss black for original appearance. Reference P/N 2863 057.
|
 |
"1746" - Alternator Adjusting Strap - (1) Required - $39 Each A quality reproduction alternator adjusting strap formed from the correct gauge steel with the correct emboss features to strengthen the mounting arm. Used on 1969-74 B & E-Body Big Block applications with Air Conditioning without Leece-Neville alternator. Includes the correct 5/16-18 mounting screw for the alternator. Powder coated low gloss black for original appearance. Reference Chrysler part number 2951 746.
|
 |
"1868" - Alternator Adjusting Strap - (1) Required - $39 Each A quality reproduction alternator adjusting strap formed from the correct gauge steel with the correct emboss features to strengthen the mounting arm. Used on 1970-74 B & E-Body Small Block applications with Air Conditioning. Includes the correct 5/16-18 mounting screw for the alternator and the 3/8-16 mounting bolt for the cylinder head. Powder coated low gloss black for original appearance. Reference Chrysler part number 2951 868.
|
 |
"987B" - Alternator Mounting Bolt Kit - (1) Required - $16 Each Big Block non-A/C alternator mounting bolts and spacers. Comes complete with two OE correct conical washers, three spacers, an "H" headed 6" long Grade 8 alternator mounting bolt, an "L5" headed 4 1/4" lower mounting bolt, a Grade 8 place bolt for the thermostat mounting boss, and an "LG" headed SEMS bolt for the alternator strap. All fastener head styles and plating are the best recognized examples of Original Equipment use. Some applications may vary.
|
 |
"987BH" - Alternator Mounting Bolt Kit - (1) Required - $18 Each 426 Hemi alternator mounting bolts and spacers. Comes complete with two OE correct conical washers, three spacers, an "H" headed 5 1/2" long Grade 8 alternator mounting bolt, an "L5" headed 4 1/4" lower mounting bolt, a Grade 8 place bolt for the thermostat mounting boss, and an "LG" headed SEMS bolt for the alternator strap. All fastener head styles and plating are the best recognized examples of Original Equipment use. Some applications may vary.
|
 |
"746B" - Alternator Mounting Bolt Kit with A/C - (1) Required - $23 Each 1969-74 Big Block 383 and 400 alternator mounting bolt and spacers with A/C. Comes complete with OE correct conical washer, two phosphate spacers, correct length Grade 8 alternator mounting bolt, a powder coated alternator mounting block, and two correct mounting bolts. |
 |
"746RB" - Alternator Mounting Bolt Kit with A/C - (1) Required - $15 Each 1969-74 Big Block 440 alternator mounting bolt and spacers with A/C. Comes complete with OE correct conical washer, correct size phosphated spacers, and correct length Grade 8 alternator mounting bolt.
|
 |
"794B" - Alternator Mounting Bolt Kit - (1) Required - $10 Each Pre-1970 Small Block alternator mounting bolt and spacers. Comes complete with correct conical washer, three phosphate spacers, and a 5" long bolt.
|
 |
"795B" - Alternator Mounting Bolt Kit - (1) Required - $10 Each 1970 & later Small Block alternator mounting bolt and spacers for non-A/C applications. Comes complete with correct conical washer, two phosphate spacers, and a 5 1/2" long bolt.
|
|
"AX41"
- Wire Retaining Clip for the Alternator - $7 Each Wire retaining clip for the washer pump and horn wires or positive alternator lead on the rear of the alternator. Zinc plated correct gauge steel and thermo-plastic coated for proper appearance. Comes complete with retaining screw. |
 |
"AX41A"
- Wire Retaining Clip for 1967-76 A-Body Brake Switch Wire - $7 Each Wire retaining clip for the brake system indicator switch wire on 1967-76 A-Bodies. Mounts to left inner fender at rear of shock tower. Zinc plated correct gauge steel and thermo-plastic coated for proper appearance. Comes complete with retaining screw. |
 |
"AX41T"
- Wire Retaining Clip for Manual Transmission Side Cover - $7 Each Wire retaining clip for the reverse light switch wire on 3 and 4-speed transmissions. Mounts under side cover retaining bolts at top rear and upper rear side locations. Zinc plated correct gauge steel and thermo-plastic coated for proper appearance. 2 Wire Retaining Clips required per transmission. Reference Chrysler part number 6015 382. |
 |
"BTBSET" - 1967-1969 B-Body Battery Tray Braces - $38 3-Piece Set Battery tray braces are manufactured to OEM specifications and dipped in corrosion resistant primer. Kits include correct J-nuts and mounting bolts. |
|
"BTB1" - 1967-1970 B-Body Lower Battery Tray Brace - $13 Each Battery tray braces are manufactured to OEM specifications and dipped in corrosion resistant primer. Part includes correct J-nut and pointed mounting bolt for battery tray. (2) required per vehicle for 1967-69 and only (1) brace required for 1970 applications. |
|
"BTB2" - 1966-1969 B-Body Upper Battery Tray Brace - $13 Each Battery tray braces are manufactured to OEM specifications and dipped in corrosion resistant primer. Part includes correct J-nut and mounting bolt for battery tray. (1) required per vehicle. |
 |
"BTB3"
- 1966 & 1971-1972 B-Body and 1970-1974 E-Body Battery Tray Brace - $13 Each Battery tray braces are manufactured to OEM specifications and dipped in corrosion resistant primer. Part includes correct J-nut and pointed mounting bolt for battery tray. (2) required per vehicle for 1966 and only (1) brace required for all other applications. |
 |
"BTB4" - 1963-1976 A-Body Battery Tray Brace
- $13
Each Battery tray braces are manufactured to OEM specifications and dipped in corrosion resistant primer. Part includes correct J-nut and pointed mounting bolt for battery tray. (1) required per vehicle. |
 |
"BHD01"
- Battery Hold Down Kit - $21 Each Kit 1960-1965 battery hold down kit for all body styles includes the correct zinc phosphate J-bolts with CORRECT heavy gauge wing nuts, 1/4" flat washers, and a thermo-plastic coated cross bracket. |
 |
"BHD01S"
- Battery Hold Down Strap - $17 Each 1960-1965 battery hold down strap for all body styles includes a thermo-plastic coated cross bracket. |
 |
"BHD03"
- Battery Hold Down Kit - $21 Each Kit 1966-1969 battery hold down kit for all body styles includes the correct zinc phosphate J-bolts with CORRECT heavy gauge wing nuts, 1/4" flat washers, and a thermo-plastic coated cross bracket. |
 |
"BHD03S"
- Battery Hold Down Strap - $17 Each 1966-1969 battery hold down strap for all body styles includes a thermo-plastic coated cross bracket. |
 |
"BHD04"
- Battery Hold Down Kit - $21 Each Kit 1970-1971 B & E-Body and 1970-1976 A-Body battery hold down kit includes the correct zinc phosphate J-bolts with hex coni SEMS nuts and a thermo-plastic coated cross bracket. |
 |
"BHD04S"
- Battery Hold Down Strap - $17 Each 1970-1971 B- & E-Body and 1970-1976 A-Body battery hold down strap only includes a thermo-plastic coated cross bracket. |
 |
"BHD05" - Battery Hold Down Kit - $21 Each Kit 1972-1974 B- & E-Body battery hold down kit includes the correct zinc phosphate J-bolts with hex coni SEMS nuts, fender mounting bolt, and a thermo-plastic coated cross bracket. |
 |
"BHD05S" - Battery Hold Down Strap - $17 Each 1972-1974 B- & E-Body battery hold down strap only includes a thermo-plastic coated cross bracket. |
 |
"BHD06" - Battery Hold Down Kit - $21 Each Kit 1966 & later C-Body battery hold down kit includes the correct zinc phosphate J-bolt with hex coni SEMS nuts and a thermo-plastic coated cross bracket. |
 |
"BHD06S" - Battery Hold Down Strap - $17 Each 1966 & later C-Body battery hold down strap only includes thermo-plastic coated cross bracket. |
 |
"JB-1" - J-Bolt Set - $8 Each Kit 1970-1971 Battery Hold Down J-Bolt Kit Zinc phosphate J-bolts with CORRECT 1" OD washer sems nuts.
|
 |
"JB-2" - J-Bolt Set - $7 Each Kit 1960-1969 Battery Hold Down J-Bolt Set Zinc phosphate J-bolts with CORRECT heavy gauge wing nuts and 1/4" flat washers.
|
 |
"JB-L"
- J-Bolt - $3 Each Used on all battery hold down engine side applications. Zinc phosphate as original. |
 |
"JB-M"
- J-Bolt - $3 Each Used on all battery hold down fender side applications for A, B, and E-Body from 1970-72. Zinc phosphate as original. |
 |
"JB-S"
- J-Bolt - $3 Each Used on all battery hold down fender side applications for A and B-Body from 1960-69. Zinc phosphate as original. |
 |
"WINGNUT"
- $2 Each Used on 1960-1969 battery hold down J-bolts. Stamped from heavy gauge steel to duplicate original dimensions. Zinc plated for proper appearance and a lasting shine. |
 |
"5006"
- Battery Hold Down Nuts - $3 Each Used on 1970-1976 battery hold down J-bolts. 1/4-20UNC thread with tall nut and 1" diameter conical washer. Correct in every dimension and black phosphate finished as original. 2 nuts required per vehicle. |
 |
"BT01" - Battery Tray - $33 Each Used on 1967-76 A-Body vehicles. Correct gauge metal and details of originals. Comes e-coated black. Not made in the USA.
|
 |
"BT02" - Battery Tray - $28 Each Used on 1966-69 B-Body vehicles. Correct gauge metal and details of originals. Comes e-coated black. Not made in the USA.
|
 |
"BT03" - Battery Tray - $33 Each Used on 1970-72 B-Body & 1970-74 E-Body vehicles. Correct gauge metal and details of originals. Comes e-coated black. B-Body brace mounting hole must be drilled. Not made in the USA.
|
 |
"BT04" - Battery Tray with Brace - $44 Each Used on 1962-65 B-Body vehicles. Correct gauge metal and details of originals. Comes as a set e-coated black. Not made in the USA.
|
 |
"BT05" - Battery Tray - $40 Each Used on 1963-66 A-Body vehicles. Correct gauge metal and details of originals. Comes e-coated black. Not made in the USA.
|
 |
"BT06" - Battery Tray - $40 Each Used on 1965-73 C-Body vehicles. Correct gauge metal and details of originals. Comes e-coated black. Not made in the USA.
|
 |
"BT07" - Battery Tray - $35 Each Used on 1973-74 B-Body vehicles. Correct gauge metal and details of originals. Comes e-coated black. Not made in the USA.
|
|
|
"PWS01" - Big Block Plug Wire Shield - $12 Each An exact reproduction of a hard to find plug boot shield. Bolts to the fourth HP exhaust manifold stud from the front to protect #7 spark plug wire boot. For use on mid-1969 and later B and E-Body HP Big Block applications!
|
 |
"PWS02" - Big Block Plug Wire Shield - $12 Each An exact reproduction of a hard to find plug boot shield. This spark plug shield bolts under the sixth and seventh head bolt to protect #6 and #8 spark plug wire boots. Correct for mid-1969 and later HP Big Block applications. |
 |
"PWS03" - Big Block Plug Wire Shield - $12 Each An exact reproduction of a hard to find plug boot shield. This spark plug shield bolts under the sixth and seventh head bolt to protect #6 and #8 spark plug wire boots. Correct for 1967-1969 HP Big Block applications. A second shield is required on HP C-Body and Big Block A-Body Applications to protect #5 and #7 spark plug wire boots. |
|
|
"PWS04" - Big Block Plug Wire Shield - $12 Each An exact reproduction of a hard to find early version plug boot shield. Bolts to the fourth left side exhaust manifold stud from the front to protect #7 spark plug wire boot. For use on 1967 through mid-1969 B-Body HP Big Block applications!
|
|
|
"PWS05" - Big Block Plug Wire Shield - $12 Each An exact reproduction of a hard to find early version plug boot shield. Bolts to the second to last left side exhaust manifold sleeve nut to protect #7 spark plug wire boot. For use on 1962-1965 B-Body Street Wedge Big Block applications. Also used on 1966-69 361 and 383 2-barrel and 1966 383 4-barrel B-Body applications. Includes correct indented hex head mounting bolt.
|
|
|
"PWS06" - Big Block Plug Wire Shield - $12 Each An exact reproduction of a hard to find early version plug boot shield. Bolts to the fourth right side exhaust manifold stud from the front to protect #8 spark plug wire boot. For use on 1962-1965 B-Body Street Wedge Big Block applications!
|
 |
"406" - 1969-71 440 Six Pack Coil Strap Mounting Bracket - $35 each Accurately reproduced from the correct gauge material and with the correct 1/4-28UNF x 3/4" long mounting studs. Bracket comes complete with two NOS phosphated coni keps nuts as original.
|
 |
"407" - 1970 340 Six Pack Coil Strap Mounting Bracket - $35 each Accurately reproduced from the correct gauge material and with the correct 1/4-28UNF x 3/4" long mounting studs. Bracket comes complete with two NOS phosphated coni keps nuts as original.
|
 |
"0499" - Speedometer Cable Bracket - $10 Each This bracket holds the speedometer cable and brake line to the left inner fender well on 1966-1970 B-Body cars. Made from stainless steel for longevity and appears as the original zinc finish. Comes with correct mounting screw. |
|
"0500" - Lower Positive Battery Cable Routing Bracket - $13 Each This bracket holds the positive battery cable to the left frame rail on 1966-1970 B-Body cars. Made from stainless steel for longevity and appears as the original zinc finish with proper thermo-plastic covering. Comes with correct hex head mounting screw. |
 |
"0501" - Upper Positive Battery Cable Routing Bracket - $12 Each This bracket holds the positive battery cable to the left inner fender well on 1966-1970 B-Body cars. Made from stainless steel for longevity and appears as the original zinc finish with proper thermo-plastic covering. Comes with correct mounting screw. |
 |
"FRBKIT"
- B-Body Speedo Cable/Brake Line/Battery
Cable Bracket Kit - $34 per Set This bracket kit includes one of each of #0499, #0500, and #0501. Used on 1966-1970 B-Body cars. See description of individual parts above for application and part location. |
|
|
"0502" - Positive Battery Cable Routing Bracket - $16 Each
This bracket holds the positive battery cable to the left frame rail on 1970-1974 E-Body and 1971-1974 B-Body cars. Made from stainless steel for longevity and appears as the original zinc finish with proper thermo-plastic covering. Comes with correct mounting screw. |
 |
"0504" - Firewall Wiring Clip Package - $35 per Kit
Accurate reproductions of the E-Body & 1971-72 B-Body wiring clips located on the brake pedal reinforcement bracket behind the master cylinder on all manual brake applications. Located on the rear of the power brake booster on Hemi power brake applications. Formed from correct gauge material, clear zinc plated, and thermo-plastic coated for original appearance. Kit includes two wiring clips, two correct 5/16-18UNC hex coni sems nuts to attach to firewall studs, and two 3/8" zinc plated pal nuts for hemi applications (not shown). |
 |
"612" - Firewall Wiring Clip - $24 Each
An excellent reproduction of the SHORT version of the 1966-70 B-Body wiring clip located on the brake pedal reinforcement bracket. Used on both power and standard brake applications. Formed from correct gauge galvanized material and thermo-plastic coated for original appearance. |
 |
"613" - Firewall Wiring Clip - $24 Each
An excellent reproduction of the LONG version of the 1966-70 B-Body wiring clip located on the brake pedal reinforcement bracket. Used on both power and standard brake applications. Formed from correct gauge galvanized material and thermo-plastic coated for original appearance. |
 |
"657" - Brake Booster Wiring Clip - $29 Each An excellent reproduction of the wiring harness clip that mounts to the left side power brake booster studs on E-Body & 1971-74 B-Body non-Hemi applications. Formed from correct gauge material with zinc plated clamp fingers and thermo-plastic coated for original appearance. Should be painted black with master cylinder and booster assembly for 1970 E-Body, and left natural for all other applications. Includes two 5/16” zinc plated pal nuts for mounting. |
